Back to the list

FRONT SEATS

  • 1
  • 2
  • 3
  • 4
  • 5

To move forwards or backwards

Depending on the seat, lift the bar 1 or handle 4 to release the seat. Release the handle at the desired position and make sure that it is locked.

Adjusting the height of the driver’s seat

Move lever 3 as many times as necessary:

- upwards to raise the seat,

- downwards to lower the seat.

To tilt the seatback

Depending on the seat, raise the lever 2 and tilt the seatback until it reaches the position required.

After making adjustments, make sure that the seatbacks are correctly locked in place.

To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts. When moving the seat, make sure that nothing interferes with the moving parts and their locking.

For safety reasons, carry out any adjustments when the vehicle is not being driven.

We would advise you not to recline the seatbacks too far to ensure that the effectiveness of the seat belts is not reduced.

Nothing should be placed on the floor (area in front of driver) as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.

Central armrest 5

(depending on the vehicle)

To adjust the seat’s lumbar position

Lower handle 6 to increase the support and lift it to decrease it.

Version with front bench seat for two

Depending on the vehicle, the central seatbacks may be folded down.

To fold down the seatback

Pull the 7 tab to unlock the seatback and lower the seatback A.

When lowering, tilt the headrest so that it is positioned under the centre console.

To raise the seatback

Lift the seat back and click it into place. Check that the bonnet is correctly locked.

Estate version flat position

Depending on the vehicle, the seatback on the passenger side may be folded down onto the seat base to create a flat position.

- Deactivate the front passenger airbag CHILD SAFETY: deactivating, activating airbag front passenger ;

- hold handle 4 and move the seat as far back as possible;

- hold the top of the seatback to lower it;

- pull the lever 2 and pull the seatback down and forwards. While lowering, tilt the headrest 8 to position it under the dashboard;

- press on the seat base to ensure that it is correctly positioned on the floor;

- make sure that there is nothing which will prevent the seat from moving;

- the seat locks automatically. Check that the bonnet is correctly locked.

Be sure to hold the seatback when placing it in the flat position.

Risk of injury.

The label B on the seat base reminds you of these instructions.

Maximum weight on the seat in the flat position: 80 kg, with the weight evenly distributed.

The label B on the seat base reminds you of these instructions.

Repositioning the seat

Make sure that nothing prevents the seat from moving.

- Pull lever 2 and lift the seatback, ensuring it is correctly locked;

- reposition the seat base, placing your hand on the front of the seat base.

When the rear bench seat is folded down, move the front seats carefully.

Remember to reactivate the front passenger airbag before a passenger occupies the seat CHILD SAFETY: deactivating, activating airbag front passenger.

Put your hand on the front of the seat base when repositioning it.

Risk of trapping.

When the front seatback is in the flat position, you must deactivate the front passenger airbag.

Risk of serious injury if the airbag is deployed while objects are resting on the seatback in flat position.

Van version flat position

The seatback on the passenger side may be folded down onto the seat base to create a flat position.

- Deactivate the front passenger airbag CHILD SAFETY: deactivating, activating airbag front passenger ;

- check that the floor is clear of any objects;

- unlock the seat base by lifting the handle 10 and move the seat forwards, onto the floor (movement D) by taking it by the rear section C;

- press on the seat base to ensure that it is correctly positioned on the floor. There is a risk the seatback being scratched if it is incorrectly positioned;

- remove the headrest 9 from the seat;

- store the headrest 9 in its housing under the seat base;

- unlock the seatback by lifting handle 10 again and position it horizontally (movement E).

The label F on the side of the seat base reminds you of these instructions.

Do not use the headrest housing 9 to store any other objects.

Risk of damage to the seat wiring.

The 11 rings located on each side of the front passenger seat can be used to secure the load placed on the seat in the flat-floor position.

For your safety, fasten down any objects transported with the seat in flat-floor position.

Maximum weight on the seat in the flat position: 80 kg, with the weight evenly distributed.

Maximum height limit for objects on the seat in flat-floor position: 50 cm.

The label G on the side of the seat base reminds you of these instructions.

To put the seat back in the comfort position, proceed in the reverse order. Check that the headrest is positioned correctly.

Remember to reactivate the front passenger airbag before a passenger occupies the seat CHILD SAFETY: deactivating, activating airbag front passenger.

When the front seatback is in the flat position, you must deactivate the front passenger airbag.

Risk of serious injury if the airbag is deployed while objects are resting on the seatback in flat position.

The label F on the side of the seat base reminds you of these instructions.

Heated seats

With the ignition on:

- pressing the switch 12 on the required seat for the first time activates the heating system on high. Both integrated switch warning lights come on;

- pressing the switch for the second time changes the heating to low. One integrated warning light comes on;

- pressing for the third time turns the heating off.

Operating faults

When an operating fault is detected, the warning light of the 12 switch for the seat concerned switches-off after approximately five seconds.

Consult an approved dealer.