EXTERIOR LIGHTING AND SIGNALS
š Side lights
Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
á Main beam headlights
With the dipped beam headlights lit, push stalk 1. This indicator light on the instrument panel comes on.
To return to the dipped headlight position, pull the stalk 1 towards you again.
k Dipped beam headlights
Manual operation
Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
Automatic operation
Turn the ring 3 until the AUTO symbol is opposite the mark 2: with the engine running, the dipped beam headlights switch on or off automatically depending on the brightness of the light outside, without any action on stalk 1.
Before driving at night: check that the electrical equipment is operating correctly. As a general precaution, check that the lights are not obscured (by dirt, mud, snow or objects being transported).
In mode AUTO, with the main beam headlights on, you can still return to dipped beam by pulling stalk 1 towards you.
When driving on the left in a left-hand drive vehicle (or vice versa), drivers must readjust their lights throughout their stay (see “Adjusting headlight beams” in Section 1).
Automatic main beam headlights
Depending on the vehicle, this system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction.
The main beam headlights come on automatically if:
- exterior light is weak;
- no other vehicles or lighting are detected;
- the vehicle speed is above approximately 25 mph (40 km/h).
If any of the above conditions are not fulfilled, the system switches to dipped beam headlights.
The “automatic main beam headlights” system should under no circumstances be used to replace driver attention and responsibility with regard to vehicle lighting and adapting to light, visibility and traffic conditions.
The system may encounter difficulties under certain conditions, including:
- extreme weather conditions (rain, snow, fog, etc.);
- obstruction in front of the windscreen or camera;
- when a following or oncoming vehicle has weak or hidden lighting;
- incorrect settings for the front headlights;
- reflective systems;
- ...
Switching on
Vehicles fitted with a multimedia system
From the multimedia screen 4, select the “Vehicle” menu, “Driving assistance”, “Automaticmain beam lights” then choose “ON" or "OFF".
Vehicles not fitted with a multimedia system
- With the vehicle at a standstill, press and hold the switch 5 OK to access the settings menu;
- repeatedly press the control 6 up or down until you reach the “Driving assistance” menu. Press the switch 5 OK;
- repeatedly press the control 6 up or down until you reach the Automaticmain beam lights menu, then press the switch 5 OK.
- press the switch 5 OK again to activate or deactivate the function:
Activation/deactivation
To activate automatic main beam headlights:
- turn the ring 3 until the AUTO symbol is opposite the mark 2.
- push the stalk 1.
Warning light comes on the instrument panel.
To deactivate automatic main beam headlights:
- pull the stalk 1 towards you;
- or turn the ring 3 to a position other than AUTO;
Warning light goes out on the instrument panel.
Note: make sure the windscreen is not obscured (dirt, mud, snow, condensation etc.).
Automatic main beam headlights (continued)
Operating faults
When the message “Check auto lighting” appears on the instrument panel, the system is deactivated.
Consult an approved dealer.
Using the portable navigation system at night in the windscreen area below the camera may disturb the operation of the “automatic main beam headlights” system (risk of reflection on the windscreen).
Daytime running lights function
The daytime running lights come on automatically with no action on stalk 1 when the engine is started, and they go off once the engine is switched off.
Operating faults
When the message “Check lighting” with warning light © is displayed and warning light k flashes on the instrument panel, this indicates that there is a lighting fault.
Consult an approved dealer.
Switching off the lights
There are two possibilities:
- manually, move ring 3 to position 0;
- automatically, the lights will go out when the engine is switched off, the driver’s door is opened or the vehicle is locked. In this case, the next time the engine is started the lights will be switched back on according to the position of the ring 3.
Lights-on reminder buzzer
A warning beep sounds when the driver’s door is opened to warn you that the lights are still on.
“See-me-home lighting” function
This function allows you to briefly switch on the dipped beam headlights (to provide light when opening a gate, etc.).
With the engine and lights switched off and the ring 3 in position 0 or AUTO, pull the stalk 1 towards you: the dipped beam headlights come on for approximately thirty seconds. To increase this duration, you may pull the stalk up to four times (total time restricted to two minutes). The message “Follow-me home for _ _ _” along with the time the lights will be on for is displayed on the instrument panel to confirm this action. You can then lock your vehicle.
To switch off the lights before they go out automatically, turn ring 3 to any position, then return it to the AUTO position.
Welcome and goodbye function
(depending on the vehicle)
Once the function is activated, the daytime running lights and the rear side light light up automatically upon detecting the RENAULT card or when the vehicle is unlocked.
They switch off automatically:
- approximately one minute after lighting up;
- when starting the engine based on the position of the lighting stalk;
or
- upon locking the vehicle.
Welcome lighting under the door mirrors
With the function activated, the lights located under the door mirrors come on automatically upon detection of the RENAULT card, upon unlocking the vehicle or when opening a door.
They switch off automatically:
- approximately one minute after lighting up;
- upon starting the engine;
or
- upon locking the vehicle.
Activating/deactivating the function
From the multimedia screen, select “Vehicle”, “User settings”, “External welcome”. Choose “ON" or “OFF" to activate or deactivate the function.
g Front fog lights
Turn centre ring 4 on stalk 1 until the symbol faces mark 2, then release it.
Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel.
f Rear fog lights
Turn centre ring 7 on the stalk until the symbol faces mark 2, then release it.
Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel.
Do not forget to switch off the fog lights when they are no longer needed, to avoid inconveniencing other road users.
Switching off the lights
Turn the ring 7 again until the mark 2 is opposite the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out.
The fog lights switch off when the exterior lights are switched off.
When driving in fog or snow, or when transporting objects which are higher than the roof, the headlights do not come on automatically.
Switching on the fog lights remains the responsibility of the driver: the indicator lights on the instrument panel inform you whether the fog lights are lit (indicator light on) or not (indicator light not on).