Exterior lighting and signals

Rotate the ring 3 until the AUTO symbol is aligned with the mark 2.

The daytime running lights come on automatically (without any action on the stalk 1) when the engine is started and they switch off when the engine is switched off.

This indicator light on the instrument panel comes on.

Turn the ring 3 until the symbol is opposite the mark 2.

This indicator light on the instrument panel comes on.

Turn the ring 3 until the AUTO symbol is opposite the mark 2: with the engine on, the dipped beam headlights switch on or off automatically according to the exterior light level, without any action on the stalk 1.

Depending on the vehicle, the dipped beam headlights will appear automatically after several sweeps of the windscreen wiper blades.

(depending on the vehicle)

This function automatically adjusts the width and range of the dipped beam headlights according to the speed and weather conditions.

Turn the ring 3 until the AUTO symbol is opposite the mark 2: with the engine on.

This function can be deactivated, refer to the multimedia instructions.

When the "Check Automatic Lighting" message appears on the instrument panel, the system is deactivated.

Consult an approved dealer.

This function is part of the adaptive front lighting system. It replaces the use of the front fog lights. It may be activated in foggy or snowy weather or in any other case of poor visibility.

To activate this function, turn the ring 3 until the AUTO symbol appears opposite the mark 2, then press the rotary switch to bring the mark 4 in line with the symbol 5.

Warning light comes on the instrument panel.

To deactivate the function, rotate the rotary switch again so that the mark 4 is opposite the symbol 5.

The warning light disappears from the instrument panel.

The poor weather lights switch off when the exterior lights are switched off.

(depending on the vehicle)

In forward gear, if the dipped beam or main beam headlights are on and depending on the steering wheel angle, this function adapts the beam width to improve visibility on a bend or at a junction.

This indicator light on the instrument panel comes on.

To return to the dipped beam headlights position, push the stalk 1 again.

It uses a camera located behind the interior rear view mirror to detect vehicles that are being followed and those coming in the opposite direction.

Note: at night, in urban areas with street lighting, the automatic main beam headlights automatically switch off.

The main beam headlights come on automatically if:

If any of the above conditions are not fulfilled, the system switches to dipped beam headlights.

Note: make sure that the windscreen is not obscured (dirt, mud, snow, condensation, etc.).

The lights will go out automatically when the driver's door is opened or the vehicle is locked, or one minute after the engine is switched off.

In this case, the next time the engine is started the lights will be switched back on according to the position of the ring 3.

If the lights are on after the engine is switched off, a warning beep sounds when the driver’s door is opened to warn you that the lights are still on.

Depending on the vehicle, if the "Check lighting" message appears along with the warning light and/or the warning flashes on the instrument panel, this indicates a lighting fault.

Consult an approved dealer.

(depending on the vehicle)

Once the function is activated, the daytime running lights and the rear side lights will light up automatically upon detection of the card or when the vehicle is unlocked.

They switch off automatically:

or

For activation or deactivation of the external welcome, refer to the multimedia instructions.

This function enables you to briefly switch on the side lights and dipped beam headlights (e.g. to provide light when opening a gate).

With the engine stopped and the lights switched off, after opening the driver's door, the ring 3 in position AUTO, pull the stalk 1 towards you: the side lights and dipped beam headlights will switch on for approximately 30 seconds along with the warning lights and on the instrument panel.

To increase this duration, you may pull the stalk up to four times (total time restricted to approximately two minutes).

The "Lighting on during _ _ _" message appears with the lighting time on the instrument panel to confirm the action.

You can then lock your vehicle.

To switch off the lights before they switch off automatically, turn the ring 3 to any position, then return it to position AUTO.

Note: if the Welcome and Goodbye function is activated, once the engine is switched off, the procedure for deactivating the "See-me-home lighting" function must be carried out before pulling the stalk (otherwise the lights remain lit by the Welcome and Goodbye function).

Warning light comes on the instrument panel.

Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel.

To avoid inconveniencing other road users, remember to switch off this light when it is no longer needed.

To deactivate the function, rotate the rotary switch again so that the mark 4 is opposite the symbol 7.

The warning light disappears from the instrument panel.

The rear fog lights switch off when the exterior lights are switched off.