Back to the list

Parking distance control

  • 1
  • 2
  • 3
  • 4
  • 5

Parking distance control

Operating principle

Ultrasonic sensors, indicated by arrows 1, are fitted in the bumpers to measure the distance between the vehicle and an obstacle.
This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to 30 centimetres from the obstacle.
Depending on the configuration of the vehicle, the system detects obstacles to the front, the rear and the sides of the vehicle.
The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h).
The function does not take into account towing or carrying systems that are not recognised by the system.

Location of the ultrasonic sensors 1

Ensure that the ultrasonic sensors indicated by arrows 1 are not obscured (by dirt, mud, snow, a badly fitted/attached number plate), impacted, modified (including paintwork) or obstructed by any accessory fitted to the rear and/ or, depending on the vehicle, to the front or sides of your vehicle.
WARNING
This function is an additional aid that indicates the distance between the vehicle and an obstacle whilst reversing, using sound signals.
Under no circumstances should it replace the driver’s care or responsibility whilst reversing.
The driver should always be ready for sudden incidents while driving : always ensure that there are no small, narrow moving obstacles (such as a child, animal, pushchair, bicycle, stone, post, etc.) in the blind spot when manoeuvring.
Note : the display 2 shows the vehicle surroundings and emits beeps.
It is necessary to travel a few metres before the side detection is activated.
If all areas have a grey background, the whole area around the vehicle is being monitored :
  • A : analysis of the vehicle surroundings in progress ;
  • B : analysis of the vehicle surroundings carried out.
Note : for vehicles fitted with the “360° camera” function 360° CAMERA, analysis of the vehicle surroundings (areas A and B) is not displayed in “Bird’s eye view” or “Side view” mode.

Operation

Most objects located less near the front, rear and sides of the vehicle are detected.
WARNING
An impact to the underside of the vehicle while manoeuvring (e.g. striking a post, raised kerb or other street furniture) may result in damage to the vehicle (e.g. deformation of an axle).
To avoid any risk of accident, have your vehicle checked by an approved dealer.
Depending on the distance of the obstacle, the frequency of the beep will be higher while approaching it, and will become a continuous beep around 30 cm away for obstacles to the sides, and around 30 cm for obstacles to the front or rear. The green, orange (or yellow depending on the vehicle) and red zones will be displayed on the C display.
Note : in the event of a change in trajectory during a manoeuvre, the risk of collision with an obstacle may be signalled late.
Detection of obstacles to the side
Depending on the direction of the wheels, the system determines the trajectory of the vehicle and notifies the driver of any risk or otherwise of a collision with an obstacle 3 to the side of the vehicle.
WARNING
An impact to the underside of the vehicle while manoeuvring (e.g. striking a post, raised kerb or other street furniture) may result in damage to the vehicle (e.g. deformation of an axle).
To avoid any risk of accident, have your vehicle checked by an approved Dealer.
If a side obstacle is detected :
  • the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the display D ;
  • if there is no risk of collision, no beep will sound when approaching the obstacle. Green, orange and red zones will be displayed interspersed on the display D.
Note : in the event of a change in trajectory during a manoeuvre, the risk of collision with an obstacle may be signalled late.

Activation/deactivation

Vehicles fitted with a multimedia screen 4
To activate or deactivate the various zones covered by the ultrasonic detectors, please refer to the multimedia instructions.
Select “ON” or “OFF”.
Note
depending on the vehicle, the rear detection zone cannot be deactivated.
Vehicles not fitted with a multimedia screen
With the vehicle stopped, press the 5 switch as many times as required to reach the “Vehicle” tab ;
press the 6 or 7 control repeatedly to reach the “Settings” menu. Press the switch 8OK ;
press the 6 or 7 control repeatedly to reach the “PARKING ASSIST” menu. Press the switch 8OK.
Note
depending on the vehicle, the rear detection zone cannot be deactivated.

Adjustment

Vehicles fitted with a multimedia screen 4
Depending on the vehicle, with the engine running, some settings can be adjusted from the multimedia screen 4. Please refer to the multimedia instructions for further information.
Parking distance control audio volume
Adjust the volume of the parking distance control by pressing + or -.
System sound
Enables the system sound to be chosen.
Deactivating the system sound
Activate or deactivate the parking distance control sound.
Note : if you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
Tip
When the vehicle is travelling at a speed below approximately 6 mph (10 km/h), some noises (motorcycle, lorry, pneumatic drill etc.) may trigger the beeping sound of the parking distance control.
Vehicles not fitted with a multimedia screen
  • With the vehicle stopped, press the 5 switch as many times as required to reach the “Vehicle” tab ;
  • press the 6 or 7 control repeatedly to reach the “Settings” menu. Press the switch 8OK ;
  • press the 6 or 7 control repeatedly to reach the “PARKING ASSIST” menu. Press the switch 8OK ;
  • select “Bip volume” to adjust the volume of Park Assist using control 6 or 7.

Deactivating the parking distance control manually

You must disable the function if :
  • if towing, carrying or trailer equipment that is unrecognised by the system is present in front of the ultrasonic detectors ;
  • in the event of damage to the ultrasonic sensors.

Automatic deactivation of the parking distance control

The system deactivates :
  • when the vehicle speed is above approximately 6 mph (10 km/h) ;
  • depending on the model, when the vehicle is stationary for more than approximately 5 seconds and an obstacle is detected (such as when in a traffic jam, etc.) ;
  • when you are in position N or  P;
  • when an operating fault is detected.
Note : if the vehicle is fitted with a towbar recognised by the system, only the rear Park Assist function is deactivated.

Operating faults

When the system detects an operating fault, a beep sounds for approximately three seconds each time reverse gear is selected and the message “Check parking sensors” appears on the instrument panel. Consult an approved dealer.
WARNING
An impact to the underside of the vehicle while manoeuvring (e.g. striking a post, raised kerb or other street furniture) may result in damage to the vehicle (e.g. deformation of an axle).
To avoid any risk of accident, have your vehicle checked by an approved dealer.
Tip
System servicing/repairs
  • In the event of an impact, the alignment of the sensors may be altered and their operation may consequently be affected. Deactivate the function and consult an authorised dealer.
  • Any work in the area where the sensors are located (repairs, replacements, etc.) must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
System disturbance
Some conditions can disrupt or damage the operation of the system, for example :
  • poor weather conditions (rain, snow, hail, black ice, etc.) ;
  • in the event of exposure to strong electromagnetic waves (under high-voltage lines, etc.) ;
  • some types of noise (motorcycle, lorry, pneumatic drill etc.) ;
  • fitting an unsuitable towing ball or hook.
Risk of false alarms or absence of warnings
In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.
Tip
Limitation of the system operation
  • The area around the sensors must be kept clean and free of any modifications in order to ensure the proper operation of the system.
  • Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system.
  • The system may not detect objects that are too close to the vehicle.
  • The system may not provide a warning when the other vehicles or objects are travelling at a significantly different speed.
  • During a change in trajectory, during a manoeuvre, the system may report obstacles with a delay.
  • When the vehicle is towing a trailer, the rear Park Assist system must be deactivated.
Deactivating the function
You must disable the function if :
  • the area around the sensors has been damaged (rear bumper) ;
  • the vehicle is equipped with a towing device that is not recognised by the system (ball, hook, adapter, etc.).