Fuel tank

  • 1
  • 2
  • 3
  • 4
  • 5

Fuel tank

Filling the tank

Useful capacity of fuel tank: approximately 17.6 gal (80 litres).
Please observe the following instructions:
  • with the ignition off, wait at least 12 seconds before starting to fill with fuel;
  • open the driver’s door in order to open the flap 1;
  • depending on the vehicle, unlock the cap 2, then remove it and attach it to the flap 1;
  • when filling the tank partially, add at least 2.2 gallons (10 litres) of fuel.
If these instructions are not observed, the tank filling level will not be taken into account on the instrument panel.
Tip
After filling, check that the cap and cover are closed.

Filling with fuel

When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made to maintain an expansion volume.
Make sure that no water enters the fuel tank during filling.
After filling, refit the cap 2 and close the flap 1 to prevent any water or foreign bodies from entering the system.
Always make sure that the cap 2, the flap 1 and its perimeter remain clean and free of dust, mud, dirt, etc.
Tip
Fuels that comply with the European standards with which vehicle engines marketed in Europe are compatible ENGINE IDENTIFICATION, ENGINE SPECIFICATIONS.

Special case

When the vehicle has been stationary for around three months, you must add fuel to prevent damage to the fuel pump.
To do this, with the ignition off, fill up with fuel or add at least approximately 2.20 gallons (10 litres) then start the engine to operate the pump and renew the fuel in the circuit.
If it is not possible to add at least 2.20 gallons (10 litres) of fuel due to the fuel level in the tank, drive the vehicle until the tank has capacity.

Fuel grade

It is essential to use diesel. Make sure that no water enters the tank accidentally during filling. The sealing system and its surrounding area must be dust-free.
Use a high-grade fuel that complies with the specific or equivalent legislation in force in the country where the vehicle is marketed. It must comply with the indications shown on the label located on the flap 1ENGINE IDENTIFICATION, ENGINE SPECIFICATIONS.
WARNING
To fill up with fuel, the engine must be off (and not only on standby in the case of vehicles equipped with the "Stop and Start" function): you must switch off the ignition , STOP AND START FUNCTION.
Fire hazard.
WARNING
Do not mix even small amounts of petrol (unleaded or E85) with diesel.
Do not use ethanol-based fuel if your vehicle is not compatible with this fuel.
Do not add reagent to the fuel – otherwise you risk damaging the engine REAGENT TANK.
If you wish to add an additive to the fuel, use a product approved by our Technical Department.
Consult an approved dealer.
WARNING
Fuel filler cap: this is a specific type.
If you have to replace it, make sure it is identical to the original cap. Contact an approved Dealer.
Never place the cap near a source of heat or flame.
Do not wash the filler area with a high pressure washer.
WARNING
No modifications whatsoever are permitted on any part of the fuel supply system (electronic unit, wiring, fuel circuit, injector, protective covers, etc.) as this may be dangerous (unless undertaken by qualified Network personnel).
WARNING
Persistent smell of fuel
If you notice a persistent fuel odour you should:
  • stop the vehicle when traffic conditions allow it and switch off the ignition;
  • switch on the hazard warning lights and ask your passengers to leave the vehicle and stay clear of the traffic;
  • contact an authorised dealer.
WARNING
Please note when working close to the engine that it may be hot. The engine cooling fan may also start at any moment. The label in the engine compartment reminds you of this.
Risk of injury.

Repriming the fuel circuit

After a breakdown due to the vehicle completely running out of fuel, the system must be reprimed before the engine is restarted:
  • turn the ignition key to the "On" position MIGNITION SWITCH and wait around 10 seconds before starting to allow the fuel circuit to be primed;
  • turn the key to D position. If the engine does not start, repeat the procedure;
  • if the engine does not start after ten attempts, please contact an approved dealer.
Tip
The peripheral components (alternator, starter, engine mountings etc.) should be protected from diesel splashes.